http://schema.org/InStock
Produktkode: 265aa
Tilgjengelighet: 4
Weight: 20.00g

POWER-1212-T2000 Hi-Speed Wireless RF Transceiver Model w/ Antenna

Pris: kr. 550,00

 
- Model: POWER-1212-T2000
- Color: Green
- Material: PCB
- High anti-jamming and sensitivity with FSK, CRC verify and FEC function
- Provides multi channels for select
- Supports modify series speed, transmit power, RF rate online or by MCU
- Working voltage: 2.1~3.6V / 4.8~5.2V
- Working frequency: 390~470MHz
- Transmit power: 30dBm (Max.)
- Air transmit power: 1K, 2K, 5K, 10K, 24K, 28K, 32Kbps
- Transmit current: Denne e-postadressen er beskyttet mot programmer som samler e-postadresser. Du må aktivere javaskript for å kunne se den.; 35mA@5V;
- Continuous receive current: Denne e-postadressen er beskyttet mot programmer som samler e-postadresser. Du må aktivere javaskript for å kunne se den.; 35mA@5V
- Sleep current: 5uA
- Sensitivity: -110dBm@1Kbps
- Series transmit speed: 1200 / 2400 / 4800 / 9600 / 19200 / 38400 / 57600bps
- Max. data: 512byte
- Parameter modification times: 300K
- Up to 5000 meters working range
- Standard DIP pin pitch
- Supports wake-on-wireless
- With heatsink and antenna
 
Dimensions: 2.83 in x 1.57 in x 0.47 in (7.2 cm x 4.0 cm x 1.2 cm)
Weight: 1.02 oz (29 g)

The Power UTC-4432-T2000E (2W / +33 dBm RF transceiver module by Hangzhou NewMsg Technologies) uses a 19-pin footprint.

Pin Layout Overview

  • Primary Interface (7-pin header on the left): Pin-compatible with the standard low-power UTC-4432 module. It contains the main logic power, ground, serial UART, mode-selection, and status pins.

  • Side Headers (12 pins total across both sides): Dedicated to the 5V high-frequency (HF) power amplifier supply and reserved/advanced feature pins. Leave all unused advanced feature pins floating (unconnected).

Core Functional Pins

Because the exact physical pin numbering is printed on the module's silkscreen and illustrated in the manufacturer's mechanical diagram, verify the silkscreen labels on your board against these functional definitions:

Pin Name Direction Function & Wiring
3.3V (VCC) Power In 3.3V supply for the core logic and RF transceiver.
5V Power In 5V supply for the 2W HF power amplifier stage. Both 3.3V and 5V rails must be powered simultaneously for full operation.
GND Ground Common ground for both the 3.3V and 5V power supplies.
RXD Input UART data receive (3.3V TTL); connect to the host MCU's TXD pin.
TXD Output UART data transmit (3.3V TTL); connect to the host MCU's RXD pin.
SET_A Input Operating mode selection bit A (connect to MCU GPIO or tie high/low).
SET_B Input Operating mode selection bit B (connect to MCU GPIO or tie high/low).
AUX Output Status indicator (goes LOW during RF transmission or when serial output data is ready; HIGH when idle). Connect to an MCU interrupt pin, or leave floating if unused.

Mode Selection (SET_A & SET_B)

The module's operating state is controlled by the logic levels on SET_A and SET_B:

SET_A SET_B Mode Behavior
0 (LOW) 0 (LOW) Normal (Mode 1) Half-duplex transparent wireless transmission and continuous listening.
0 (LOW) 1 (HIGH) Wake-up TX (Mode 2) Transmits a wake-up preamble to wake sleeping receivers.
1 (HIGH) 0 (LOW) Power-Saving RX (Mode 3) Periodically wakes (e.g., every 1 s) to listen for incoming RF packets.
1 (HIGH) 1 (HIGH) Configuration (Mode 4) Configures RF parameters over UART (fixed at 9600 bps, 8N1).

Note: Never power on the T2000E (2W) without a matched antenna connected to the RF port, as reflected power can damage the amplifier stage.

The UTC-4432-T2000E (V6A) is a medium-power (2W / +33 dBm) 433 MHz transparent wireless serial (UART) transceiver module by Hangzhou NewMsg Technology. Setting it up requires dual-rail power (both 3.3V and 5V), proper antenna termination before powering on, and setting the SET_A and SET_B mode pins to enter either configuration or normal transmission mode.

RF Amplifier & Voltage Safety

Never power on the UTC-4432-T2000E without a 50-ohm 433 MHz antenna connected to the RF port—operating a 2W (+33 dBm) amplifier into an open load can permanently burn out the RF front-end. Additionally, keep UART and mode control logic at 3.3V TTL levels unless your carrier board includes built-in level shifters.

1. Hardware Wiring & Power Setup

The module uses two separate power rails: a 3.3V supply for the microcontroller/RF logic and a dedicated 5V supply (4.8V–5.2V) for the 2W power amplifier.

Module Pin Connection Target Notes / Function
5V (PA) Dedicated 5V DC Supply (≥ 1.5A) Powers the 2W RF amplifier. Do not draw from a weak USB-TTL 5V pin.
3.3V (VCC) Regulated 3.3V Supply Powers the onboard MCU and RF logic.
GND Common Ground Tie 5V GND, 3.3V GND, and MCU/Adapter GND together.
TXD Host / Adapter RX Serial data output from the RF module (3.3V TTL).
RXD Host / Adapter TX Serial data input to the RF module (3.3V TTL).
SET_A Host GPIO or Jumper Mode control pin A (3.3V logic).
SET_B Host GPIO or Jumper Mode control pin B (3.3V logic).
AUX Host Interrupt Pin (Optional) Goes LOW while transmitting/receiving; HIGH when idle. Leave floating if unused.

2. Operating Modes (SET_A / SET_B)

Control how the transmitter behaves by pulling SET_A and SET_B High (1 = 3.3V) or Low (0 = GND):

Mode SET_A SET_B Function
Mode 1: Normal 0 (LOW) 0 (LOW) Standard transparent half-duplex TX/RX. Receiver stays awake continuously.
Mode 2: Wake-Up TX 0 (LOW) 1 (HIGH) Adds a long wake-up preamble to transmissions so sleeping Mode 3 receivers can hear them.
Mode 3: Power-Save RX 1 (HIGH) 0 (LOW) Dormant state; wakes periodically (default 1s) to listen for Mode 2 preambles. Cannot transmit.
Mode 4: Sleep / Config 1 (HIGH) 1 (HIGH) Disables RF and allows HEX parameter configuration via UART at fixed 9600 bps, 8N1.

3. Step-by-Step Setup & Link Verification

1.Attach Antenna and Wire Power/UART:Before applying power.

Screw a 433 MHz antenna onto the SMA/IPEX connector. Wire 3.3V, 5V, GND, TXD, and RXD to your USB-to-TTL adapter or microcontroller, ensuring all grounds are shared.

Verification: Confirm with a multimeter that 5V is between 4.8V and 5.2V and RXD/TXD are crossed (TXD to RX, RXD to TX).

2.Enter Configuration Mode (Mode 4):Optional if using factory defaults.

Pull both SET_A and SET_B to HIGH (3.3V), then power on the module. Open a serial terminal at 9600 baud, 8 data bits, No parity, 1 stop bit (8N1) in HEX mode to read/write frequency, air rate, power (+33 dBm max), and node/destination addresses using the manufacturer's HEX configuration utility or command frames.

Verification: The module responds with valid HEX acknowledgement frames and saves your parameters to flash. (Note: Factory defaults are 9600 bps, no parity, 1s wake time, +33 dBm).

3.Switch Both Modules to Normal Mode (Mode 1):

Pull both SET_A and SET_B to LOW (GND) on both the transmitter and receiver units. Ensure both modules share identical RF frequency, air data rate, and matching destination/local addresses.

Verification: The AUX pin rests at HIGH (3.3V) when idle.

4.Test Wireless Transparent Transmission:

Send an ASCII or HEX string from the transmitter's host UART (at your configured baud rate, default 9600 bps).

Verification: On the transmitter, AUX pulses LOW during RF packet transmission and returns HIGH when finished. On the receiver, AUX pulses LOW and the exact string appears on its TXD pin.

Det er ingen tilbakemeldninger for dette produktet
Skriv en tilbakemelding
Facebook-kommentar